华西口腔医学杂志 ›› 2020, Vol. 38 ›› Issue (5): 525-531.doi: 10.7518/hxkq.2020.05.009

• 临床研究 • 上一篇    下一篇

激光熔融数字化导板技术辅助钙化根管的治疗

张婷1,2(), 陈度3, 苗雷英1,2, 谢思静1,2, 汤旭娜1,2,4()   

  1. 1. 南京大学医学院附属口腔医院,南京市口腔医院牙体牙髓病科,南京 210000
    2. 南京大学医学院附属口腔医院,南京市口腔医院中心实验室,南京 210000
    3. 南京大学医学院附属口腔医院,南京市口腔医院修复科,南京 210000
    4. 计算机软件新技术国家重点实验室(南京大学),南京 210000
  • 收稿日期:2020-01-17 修回日期:2020-03-15 出版日期:2020-10-01 发布日期:2020-10-14
  • 通讯作者: 汤旭娜 E-mail:zhangting7700@163.com;xunatang@126.com
  • 作者简介:张婷,硕士,E-mail:zhangting7700@163.com
  • 基金资助:
    南京市医学科技发展资金项目(YKK16157);南京市科技计划项目(201715040);南京大学计算机软件新技术国家重点实验室资助项目(KFKT2018B16);科教强卫工程江苏省青年医学人才(QNRC2016120);江苏省青年医学人才资助项目(2017)

Guided endodontic access of calcified root canal by laser melting templates

Zhang Ting1,2(), Chen Du3, Miao Leiying1,2, Xie Sijing1,2, Tang Xuna1,2,4()   

  1. 1. Dept. of Cariology and Endodontics, Nanjing Stomatological Hospital, Medical School of Nanjing University, Nanjing 210000, China
    2. Central Laboratory of Stomatology, Nanjing Stomatological Hospital, Medical School of Nanjing University, Nanjing 210000, China
    3. Dept. of Prosthodontics, Nanjing Stomatological Hospital, Medical School of Nanjing University, Nanjing 210000, China
    4. State Key Lab. for Novel Software Technology, Nanjing University, Nanjing 210000, China
  • Received:2020-01-17 Revised:2020-03-15 Online:2020-10-01 Published:2020-10-14
  • Contact: Tang Xuna E-mail:zhangting7700@163.com;xunatang@126.com
  • Supported by:
    Nanjing Medical Science and Technique Development Foundation(YKK16157);Nanjing Foundation for Development of Science and Technology(201715040);Project of State Key Lab. for Novel Software Technology(Nanjing University)(KFKT2018B16);Project of Invigorating Health Care through Science, Technology and Education Jiangsu Provincial Medical Youth Talent(QNRC2016120);Jiangsu Provincial Medical Youth Talent(2017)

摘要: 目的 利用激光熔融数字化导板技术获得钙化根管治疗的新方法,并评估其准确性。方法 采用激光熔融数字化导板技术辅助2例前牙钙化根管的治疗。术前使用锥形束CT(CBCT)扫描患者上颌牙,建立三维牙体硬组织根管系统模型;制取患者上颌印模,三维扫描仪扫描模型,整合CBCT及三维扫描数据,通过Mimics 19.0及3-matic 11.0软件设计开髓路径,使用钴铬合金激光熔融法打印导板,在根管导板引导下开髓及打通钙化段根管,完成根管治疗。测量术前开髓设计路径和术后实际路径的位置和角度偏差。结果 2例患牙均获得较好的治疗效果。病例1的开髓角度偏差为1.77°,钻基底偏差为0.403~0.497 mm,钻尖端偏差为0.433~0.537 mm。病例2的角度偏差为3.26°,钻基底偏差为0.183~0.347 mm,钻尖端偏差为0.310~0.463 mm。结论 钴铬合金激光熔融根管导板辅助建立根管通道是治疗钙化根管的有效方法,可作为钙化根管治疗的新策略。

关键词: 引导根管治疗, 激光熔融导板, 钙化根管, 锥形束CT

Abstract:

Objective The aim of this study is to treat calcified root canal and assess the accuracy of guided endodontics using laser melting templates. Methods Two cases with calcified anterior teeth were treated with laser melting templates. Cone beam computed tomography (CBCT) was used to scan the maxillary teeth of patients before surgery to establish the root canal system model. The maxillary impression of the patient was made and it was scanned by a 3D scanner. The CBCT scans were matched with surface scans of plaster model. Mimics 19.0 and 3-matic 11.0 software were used to design the virtual planning to access cavities. The templates were produced by laser melting 3D printing. Access cavity was prepared under the guidance of laser melting template. Then the deviations of planned and prepared cavities in three dimensions and angle were measured. Results The two teeth obtained satisfactory results. The first case had a angle deviation of 1.77°, a drilling base deviation of 0.403-0.497 mm, and a tip of 0.433-0.537 mm. The second case had a angle deviation of 3.26°, a drill base deviation of 0.18-0.347 mm, and a tip of 0.310-0.463 mm. Conclusion Laser melting template-guided endodontics is an effective technique for the treatment of calcified root canal and can be used as a new strategy for the treatment of calcified canal.

Key words: guided endodontics, laser melting templates, calcified root canal, cone beam computed tomography

中图分类号: