厚度配比对2种牙科陶瓷疲劳行为的影响研究

华西口腔医学杂志

厚度配比对2种牙科陶瓷疲劳行为的影响研究

刘伟才郭凌云王海波吴珺华苏俭生

同济大学口腔医院修复科，上海200072

收稿日期:2009-02-25 修回日期:2009-02-25 出版日期:2009-02-20 发布日期:2009-02-20
通讯作者: 苏俭生，Tel: 13611669191
作者简介: 刘伟才（1975-），男，湖南人，讲师，博士
基金资助:
上海市科委科技攻关重点资助项目（054119533）

The influence of thickness ratios on the fatigue behaviors of two kinds of dental ceramic

LIU Wei-cai, GUO Ling-yun, WANG Hai-bo, WU Jun-hua, SU Jian-sheng

Dept. of Prosthodontics, School of Stomatology, Tongji University, Shanghai 200072, China

Received:2009-02-25 Revised:2009-02-25 Online:2009-02-20 Published:2009-02-20
Contact: SU Jian-sheng，Tel: 13611669191

摘要/Abstract

摘要：

目的考察不同厚度配比的EmpressⅡ热压铸造陶瓷和GI-Ⅱ型氧化铝渗透陶瓷层状复合结构经Hertzian循疲劳前后强度的变化。方法分别制作不同厚度配比EmpressⅡ热压铸造陶瓷和GI-Ⅱ型氧化铝渗透陶瓷圆盘状试件，应用Hertzian接触实验方法对这些试件进行循环加载，然后测试105循环加载前后试件的临界载荷。结果EmpressⅡ热压铸造陶瓷和GI-Ⅱ型氧化铝渗透陶瓷在经Hertzian循环加载后，临界载荷力的平均值比加载前均明显下降（P<0.05），并且载荷力随底层瓷厚度的下降而降低。GI-Ⅱ氧化铝渗透陶瓷在加载前后的临界载荷均明显高于EmpressⅡ热压铸造陶瓷（P<0.05）。结论循环疲劳能显著降低EmpressⅡ热压铸造陶瓷和GI-Ⅱ型氧化铝渗透陶瓷材料的强度，后者在抗碎裂能力和耐受疲劳方面均优于前者，底层瓷的强度和厚度是决定这2种材料临界载荷力的大小的主要因素。

关键词: 牙科陶瓷, 厚度配比, 循环疲劳, 临界载荷

Abstract:

Objective To investigate the intensity changes of different thickness ratios of Empress Ⅱ glass ceramic and GI-Ⅱ glass-infiltrated alumina ceramic before and after Hertzian contact cyclic fatigue. Methods Disk-shaped specimens of different thickness ratios of EmpressⅡglass ceramic and GI-Ⅱglass-infiltrated alumina ceramic were respectively fabricated. Hertzian contact technique was imposed on the specimens. Critical loads of the specimens before and after 105 cycles loading were recorded. Results The average values of critical loads of all specimens reduced significantly after cycles loading（P<0.05）, and critical loads declined with diminishing thickness of the core ceramic. The critical load of GI- Ⅱ glass-infiltrated alumina ceramic was significantly higher than Empress Ⅱ glass ceramic before and after cycle loading（P<0.05）. Conclusion Cycle loading can reduce the strengths of the two kinds of dental ceramic, and the latter is better than the former in the resistance to fracture and cyclic fatigue. Critical loads of the two kinds of dental ceramic are mainly influenced by the core ceramic′s strength and thickness.

Key words: dental ceramic, thickness ratio, cycle fatigue, critical load

刘伟才郭凌云王海波吴珺华苏俭生. 厚度配比对2种牙科陶瓷疲劳行为的影响研究[J]. 华西口腔医学杂志.

LIU Wei-cai, GUO Ling-yun, WANG Hai-bo, WU Jun-hua, SU Jian-sheng. The influence of thickness ratios on the fatigue behaviors of two kinds of dental ceramic[J]. West China Journal of Stomatology.

[1]	熊芳, 夏辉. 3种半透性测量指标的比较性研究[J]. 华西口腔医学杂志, 2017, 35(3): 281-285.
[2]	伊元夫王晨温宁林勇钊田杰谟. 牙科着色氧化钇稳定四方多晶氧化锆陶瓷的结构与性能[J]. 华西口腔医学杂志, 2009, 27(05): 473-478.
[3]	刘天爽李振春陈小冬. MarkⅡ型机加工陶瓷与VitaVM9饰面瓷结合界面的研究[J]. 华西口腔医学杂志, 2009, 27(02): 154-156.
[4]	伊元夫王晨田杰谟刘洪臣温宁. 牙科着色氧化钇稳定四方多晶氧化锆陶瓷的制备及颜色性能[J]. 华西口腔医学杂志, 2008, 26(05): 556-559.
[5]	熊芳巢永烈朱智敏. 制作工艺对牙科陶瓷半透性和颜色的影响[J]. 华西口腔医学杂志, 2007, 25(06): 564-567.
[6]	苏俭生郭凌云刘伟才. 两种牙科陶瓷材料层状结构循环疲劳行为的对比研究[J]. 华西口腔医学杂志, 2007, 25(02): 166-168.
[7]	王爱军;何小明;刘莉霞;张朝标;张敏;沈倍勇. IPS-Empress2热压铸陶瓷全冠的临床应用体会[J]. 华西口腔医学杂志, 2007, 25(01): 70-72.
[8]	莫安春,岑远坤,廖运茂,王建华. 钛表面预处理对钛—瓷剪切结合强度影响的研究[J]. 华西口腔医学杂志, 2003, 21(02): 104-106.
[9]	孟玉坤,巢永烈,廖运茂. GI-Ⅱ型渗透陶瓷全瓷底层材料透射率的测定[J]. 华西口腔医学杂志, 2002, 20(05): 367-369.
[10]	王航,巢永烈,廖运茂,朱智敏,巢齐宇,梁星. GI-Ⅱ型渗透陶瓷氧化铝粉体的研究[J]. 华西口腔医学杂志, 2002, 20(03): 164-165.
[11]	莫安春,王建华,廖运茂,岑远坤,石旭旭. 遮色瓷中结晶相对钛—瓷结合强度的影响研究[J]. 华西口腔医学杂志, 2001, 19(06): 357-359.
[12]	万乾炳，杜传诗，巢永烈，游伦. GI－Ⅰ型粉浆涂塑铝瓷核冠材料热膨胀性能测试[J]. , 1995, 13(04): 0-.
[13]	万乾炳，杜传诗，巢永烈，游伦. GI－Ⅰ型粉浆涂塑铝瓷核冠底层抗弯强度的测定[J]. , 1995, 13(04): 0-.