West China Journal of Stomatology ›› 2022, Vol. 40 ›› Issue (4): 428-435.doi: 10.7518/hxkq.2022.04.009

Previous Articles     Next Articles

Effects of loupes and microscopes on a dental technician’s working posture from ergonomic aspects

Yu Jiayi(), Lou Yuxin, Zhu Liqing, Ren Wei, Yang Xingqiang, Yu Haiyang.()   

  1. State Key Laboratory of Oral Diseases & National Clinical Research Center for Oral Diseases & Dept. of Prosthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu 610041, China
  • Received:2021-09-22 Revised:2022-04-02 Online:2022-07-25 Published:2022-07-27
  • Contact: Yu Haiyang. E-mail:649461390@qq.com;yhyang6812@scu.edu.cn
  • Supported by:
    Sichuan Science and Technology Program(2020YFS0040);Correspondence: Yu Haiyang, E-mail: yhyang6812@scu.edu.cn

Abstract:

Objective This work aimed to study the effects of loupes and microscopes on a dental technician’s working posture during practical operation from ergonomic aspects. The technician's working postures under the conditions of the naked eye, loupes, and microscopes were compared. The practical value of loupes and microscopes was assessed based on the evaluation index of working posture from ergonomic aspects. Methods Three dental technicians who were skilled in using loupes and microscopes from West China Stomatology Technology Department of Sichuan University were involved in this prospective rando-mized controlled trial. Before the operation, cameras were installed in the sagittal position, top-view position, and dorsal position of the operation. Each technician made five porcelain veneers of the right maxillary central incisor following the standard process. A chairside computer-aided design and computer-aided manufacturing (CAD/CAM) system was used to mill and layer the ceramic block under the naked eye (A: control group), 3.5× headwear loupes (B: loupe group), and 9× desktop microscopes (C: microscope group). The working posture was recorded by videos throughout the entire process. After each operation, the investigator used OpenPose to recognize the working posture. The joint angles of the arm, elbow, wrist, neck, and trunk, as well as their corresponding rapid upper limb assessment (RULA) scores, were calcula-ted by MATLAB. The working posture was assessed from ergonomic aspects based on the joint angles, RULA scores, and operation time. Statistical analysis was performed using SPSS 26.0. Results The RULA score of upper limb joint angles showed that the angles of the arm, elbow, wrist, neck, and trunk under the naked eye were 14.93°±9.44°, 120.19°±2.99°, 23.97°±2.84°, 47.27°±5.72°, and 7.76°±2.30°, respectively. All of the joint angles were significantly different among the three groups (P<0.05). Compared with the control group, the angles of the neck and trunk in the loupe group were reduced by 29.09% and 42.53%, respectively, whereas those in the microscope group were significantly reduced by 43.99% and 87.11%, respectively. Multiple comparisons by LSD for the angles of neck and trunk revealed that the loupe group and the microscope group were significantly different from the control group (P<0.05), and they were also significantly different from each other (P<0.05). The mean RULA scores were 6.24±0.34 in the control group, 5.53±0.35 in the loupe group, and 3.31±0.19 in the microscope group. Compared with the control group, the mean RULA score in the loupe group was lower, and that in the microscope group was significantly lower. The differences between every two groups were statistically significant (P<0.05). The mean RULA score in the microscope group was significantly lower than that in the loupe group (P<0.05). The average operation times of the control group, loupe group, and microscope group were (50.69±36.78), (52.01±34.65), and (59.44±35.81) min, respectively. No significant difference was found among the three groups (P>0.05). Conclusion Use of loupes and microscopes showed an improvement in ergonomics and working posture of dental technicians. Microscopes had a better effect in the ergonomic convenience of the technician than loupes.

Key words: loupes, microscopes, ergonomics, dental technicians, porcelain veneers, musculoskeletal disorders

CLC Number: